F-Tile Interlaken Intel® FPGA IP User Guide

Download PDF
ID 683622
Date 12/04/2023
Public
Document Table of Contents
Document Table of Contents x
1. About the F-Tile Interlaken Intel® FPGA IP Core 2. Getting Started 3. Parameter Settings 4. Functional Description 5. Interface Signals 6. IP Registers 7. F-Tile Interlaken Intel® FPGA IP User Guide Archives 8. Document Revision History for F-Tile Interlaken Intel FPGA IP User Guide
1. About the F-Tile Interlaken Intel® FPGA IP Core x
1.1. Features 1.2. Device Family Support 1.3. Device Speed Grade Support 1.4. Performance and Resource Utilization 1.5. Round-trip Latency 1.6. Release Information
2. Getting Started x
2.1. Installing and Licensing Intel® FPGA IPs 2.2. Generated File Structure 2.3. Specifying the IP Core Parameters and Options 2.4. Analog Parameter Settings 2.5. Reference and System PLL Clock for your IP Design 2.6. Simulating the IP Core 2.7. Compiling the Full Design and Programming the FPGA
2.1. Installing and Licensing Intel® FPGA IPs x
2.1.1. Intel® FPGA IP Evaluation Mode
2.5. Reference and System PLL Clock for your IP Design x
2.5.1. System PLL Configuration
4. Functional Description x
4.1. Data Path Flow 4.2. Interlaken Look-aside Data Path Flow 4.3. Modes of Operation 4.4. Performance 4.5. IP Reset 4.6. M20K ECC Support 4.7. Out-of-Band Flow Control 4.8. 32-bit Soft CWBIN Counters
4.1. Data Path Flow x
4.1.1. Interlaken TX Path 4.1.2. Interlaken RX Path
4.1.1. Interlaken TX Path x
4.1.1.1. Transmit Path Blocks 4.1.1.2. In-Band Calendar Bits on Transmit Side
4.1.2. Interlaken RX Path x
4.1.2.1. Receive Path Blocks 4.1.2.2. In-Band Calendar Bits on Receive Side 4.1.2.3. RX Errored Packet Handling
4.1.2.3. RX Errored Packet Handling x
4.1.2.3.1. Example With Errors and In-Band Calendar Bits
4.2. Interlaken Look-aside Data Path Flow x
4.2.1. Interlaken Look-aside TX Path 4.2.2. Interlaken Look-aside RX Path
4.2.1. Interlaken Look-aside TX Path x
4.2.1.1. Transmit Path Blocks
4.2.2. Interlaken Look-aside RX Path x
4.2.2.1. Receive Path Blocks 4.2.2.2. RX Error Handling
4.3. Modes of Operation x
4.3.1. Interleaved and Packet Modes 4.3.2. Multi-Segment Mode 4.3.3. Interlaken Look-aside Mode
4.3.1. Interleaved and Packet Modes x
4.3.1.1. Transmit User Data Interface Examples 4.3.1.2. Receive User Data Interface Example
4.3.2. Multi-Segment Mode x
4.3.2.1. Multi-Segment Interface Example
4.3.3. Interlaken Look-aside Mode x
4.3.3.1. Transmit User Data Interface Example 4.3.3.2. Receive User Data Interface Example
5. Interface Signals x
5.1. Clock and Reset Interface Signals 5.2. Transmit User Interface Signals 5.3. Receive User Interface Signals 5.4. Management Interface Signals 5.5. Reconfiguration Interface Signals 5.6. Interlaken Link and Miscellaneous Signals
1. About the F-Tile Interlaken Intel® FPGA IP Core
2. Getting Started
3. Parameter Settings
4. Functional Description
5. Interface Signals
6. IP Registers
7. F-Tile Interlaken Intel® FPGA IP User Guide Archives
8. Document Revision History for F-Tile Interlaken Intel FPGA IP User Guide

5.5. Reconfiguration Interface Signals

Table 26.  Transceiver Reconfiguration Interface Signals
Signal Name Width (Bits) I/O Direction Available In Description
reconfig_xcvr_clk 1 Input Interlaken and Interlaken Look-aside mode Transceiver reconfiguration interface clock. Supported frequency range 100-250MHz.
reconfig_xcvr_reset 1 Input Active-high synchronous reset. Assert this signal to reset the transceiver reconfiguration interface.
reconfig_xcvr_read 1 Input Read access to the hard PCS registers.
reconfig_xcvr_write 1 Input Write access to the hard PCS registers.
reconfig_xcvr_address 18+5 Input Address to access the hard PCS registers. This signal holds both the hard PCS register offset and the transceiver channel being addressed.
  • 18-bits for address
  • 5-bits for lane selection
reconfig_xcvr_writedata 32 Input When reconfig_write is high, reconfig_writedata holds valid write data.
reconfig_xcvr_readdata 32 Output After user logic asserts the reconfig_read signal, when the IP core deasserts the signal, reconfig_readdata holds valid read data.
reconfig_xcvr_readdatavalid 1 Output Valid signal for reconfig_xcvr_readdata.
reconfig_xcvr_waitrequest 1 Output Busy signal for reconfig_readdata.
reconfig_xcvr_byteenable 4 Input Transceiver reconfiguration byte enable signal.
Table 27.  Interlaken Reconfiguration Interface SignalsThese signals are only available for PAM4 mode.
Signal Name Width (Bits) I/O Direction Available In Description
reconfig_ilk_clk 1 Input Interlaken mode Interlaken reconfiguration interface clock. Supported frequency range 100-250MHz.
reconfig_ilk_reset 1 Input Active-high synchronous reset. Assert this signal to reset the Interlaken reconfiguration interface.
reconfig_ilk_read 1 Input Read access to the Interlaken reconfiguration registers.
reconfig_ilk_write 1 Input Write access to the Interlaken reconfiguration registers.
reconfig_ilk_address 14+3 Input Address to access the Interlaken reconfiguration registers.
  • 14-bits for address
  • 3-bits for FEC selection
reconfig_ilk_writedata 32 Input When reconfig_write is high, reconfig_writedata holds valid write data.
reconfig_ilk_readdata 32 Output After user logic asserts the reconfig_read signal, when the IP core deasserts the signal, reconfig_readdata holds valid read data.
reconfig_ilk_readdatavalid 1 Output Valid signal for reconfig_ilk_readdata.
reconfig_ilk_waitrequest 1 Output Busy signal for reconfig_readdata.
reconfig_ilk_byteenable 4 Input Interlaken reconfiguration byte enable signal.
Level Two Title