Low Latency E-Tile 40G Ethernet Intel® FPGA IP User Guide

Download PDF
ID 683486
Date 4/09/2024
Public
Document Table of Contents
Document Table of Contents x
1. About the Low Latency E-Tile 40G Ethernet Intel® FPGA IP 2. Low Latency E-Tile 40G Ethernet IP Core Parameters 3. Getting Started 4. Functional Description 5. Reset 6. Interfaces and Signal Descriptions 7. Control, Status, and Statistics Register Descriptions 8. Debugging the Link 9. Ethernet Toolkit Overview 10. Low Latency E-Tile 40G Ethernet Intel® FPGA IP User Guide Archives 11. Comparison Between Low Latency E-Tile 40G Ethernet Core and Low Latency 40GbE IP Core 12. Document Revision History for Low Latency E-Tile 40G Ethernet Intel® FPGA IP User Guide
1. About the Low Latency E-Tile 40G Ethernet Intel® FPGA IP x
1.1. Release Information 1.2. Low Latency E-Tile 40G Ethernet Intel® FPGA IP Supported Features 1.3. Low Latency E-Tile 40G Ethernet Intel® FPGA IP Device Family and Speed Grade Support 1.4. Resource Utilization
1.3. Low Latency E-Tile 40G Ethernet Intel® FPGA IP Device Family and Speed Grade Support x
1.3.1. Device Family Support 1.3.2. Low Latency E-Tile 40G Ethernet Intel® FPGA IP Device Speed Grade Support
3. Getting Started x
3.1. Installing and Licensing Intel® FPGA IP Cores 3.2. Specifying the Low Latency E-Tile 40G Ethernet IP Core Parameters and Options 3.3. Simulating the IP Core 3.4. Generated File Structure 3.5. Integrating Your IP Core in Your Design 3.6. Low Latency E-Tile 40G Ethernet IP Core Testbench 3.7. Compiling the Full Design and Programming the FPGA
3.5. Integrating Your IP Core in Your Design x
3.5.1. Pin Assignments 3.5.2. Ethernet Adaptation Flow 3.5.3. Placement Settings for the Low Latency E-Tile 40G Ethernet Core
3.6. Low Latency E-Tile 40G Ethernet IP Core Testbench x
3.6.1. Understanding the Testbench Behavior
4. Functional Description x
4.1. Low Latency E-Tile 40G Ethernet Core Functional Description 4.2. User Interface to Ethernet Transmission
4.1. Low Latency E-Tile 40G Ethernet Core Functional Description x
4.1.1. Low Latency E-Tile 40G Ethernet Core TX MAC Datapath 4.1.2. Low Latency E-Tile 40G Ethernet Core RX MAC Datapath 4.1.3. Link Fault Signaling Interface 4.1.4. Flow Control
4.1.1. Low Latency E-Tile 40G Ethernet Core TX MAC Datapath x
4.1.1.1. Frame Padding 4.1.1.2. Preamble Insertion 4.1.1.3. Inter-Packet Gap Generation and Insertion 4.1.1.4. Frame Check Sequence (CRC-32) Insertion
4.1.2. Low Latency E-Tile 40G Ethernet Core RX MAC Datapath x
4.1.2.1. IP Core Preamble Processing 4.1.2.2. IP Core Strict SFD Checking 4.1.2.3. Length/Type Field Processing 4.1.2.4. RX CRC Checking and Dynamic Forwarding
4.1.2.3. Length/Type Field Processing x
4.1.2.3.1. Length Checking
4.1.4. Flow Control x
4.1.4.1. TX Pause/PFC Flow Control Transmission 4.1.4.2. XON/XOFF Pause Frames
4.2. User Interface to Ethernet Transmission x
4.2.1. Order of Transmission 4.2.2. Bit Order For TX and RX Datapaths
6. Interfaces and Signal Descriptions x
6.1. TX MAC Interface to User Logic 6.2. RX MAC Interface to User Logic 6.3. Transceivers Signals 6.4. Transceiver Reconfiguration Signals 6.5. Avalon® Memory-Mapped Management Interface 6.6. Miscellaneous Status and Debug Signals 6.7. Reset Signals 6.8. Clocks 6.9. Flow Control Interface
7. Control, Status, and Statistics Register Descriptions x
7.1. PHY Registers 7.2. TX MAC Registers 7.3. RX MAC Registers 7.4. Pause/PFC Flow Control Registers
9. Ethernet Toolkit Overview x
9.1. Features
1. About the Low Latency E-Tile 40G Ethernet Intel® FPGA IP
2. Low Latency E-Tile 40G Ethernet IP Core Parameters
3. Getting Started
4. Functional Description
5. Reset
6. Interfaces and Signal Descriptions
7. Control, Status, and Statistics Register Descriptions
8. Debugging the Link
9. Ethernet Toolkit Overview
10. Low Latency E-Tile 40G Ethernet Intel® FPGA IP User Guide Archives
11. Comparison Between Low Latency E-Tile 40G Ethernet Core and Low Latency 40GbE IP Core
12. Document Revision History for Low Latency E-Tile 40G Ethernet Intel® FPGA IP User Guide

3.2. Specifying the Low Latency E-Tile 40G Ethernet IP Core Parameters and Options

The Low Latency E-Tile 40G Ethernet parameter editor allows you to quickly configure your custom IP variation. Use the following steps to specify IP core options and parameters in the Quartus® Prime Pro Edition software.
  1. In the Quartus® Prime Pro Edition, click File > New Project Wizard to create a new Quartus® Prime project, or File > Open Project to open an existing Quartus® Prime project. The wizard prompts you to specify a device.
  2. In the IP Catalog (Tools > IP Catalog), locate and double-click the name of the IP core to customize. The New IP Variation window appears.
  3. Specify a top-level name for your custom IP variation. The parameter editor saves the IP variation settings in a file named <your_ip> .ip.
  4. Click OK. The parameter editor appears.
  5. On the IP tab, specify the parameters for your IP core variation. Refer to Low Latency E-Tile 40G Ethernet IP Core Parameters for information about specific IP core parameters.
  6. Optionally, to generate a simulation testbench or compilation and hardware design example, follow the instructions in the Low Latency E-Tile 40G Ethernet Design Example User Guide .
  7. Click Generate HDL. The Generation dialog box appears.
  8. Specify output file generation options, and then click Generate. The IP variation files generate according to your specifications.
  9. Click Finish. The parameter editor adds the top-level .ip file to the current project automatically. If you are prompted to manually add the .ip file to the project, click Project > Add/Remove Files in Project to add the file.
  10. After generating and instantiating your IP variation, make appropriate pin assignments to connect ports.
Related Information
Level Two Title