Intel® Quartus® Prime Pro Edition User Guide: Partial Reconfiguration

ID 683834
Date 10/04/2021
Public

A newer version of this document is available. Customers should click here to go to the newest version.

Document Table of Contents

2.3.5. Ports

The Partial Reconfiguration Controller Intel® Arria® 10 /Cyclone 10 FPGA IP includes the following interface ports.
Figure 44.  Partial Reconfiguration Controller Interface Ports (Internal Host)
Figure 45. Partial Reconfiguration Controller Interface Ports (External Host)
Table 23.  Clock/Reset Ports
Port Name Width Direction Function

nreset

1

Input

Asynchronous reset for the PR Controller IP core. Resetting the PR Controller IP core during a partial reconfiguration operation initiates the withdrawal sequence.

clk

1

Input

User input clock to the PR Controller IP core. The IP core has a maximum clock frequency of 100MHz.

The IP core ignores this signal during JTAG debug operations.

Table 24.  Freeze Interface Port
Port Name Width Direction Function

freeze

1

Output

Active high signal that freezes the PR interface signals of any region undergoing partial reconfiguration. De-assertion of this signal indicates the end of PR operation.

Use the Partial Reconfiguration Region Controller IP rather than the Partial Reconfiguration Controller IP freeze signal.

Table 25.  Conduit Interface PortsThese ports are available when Enable Avalon® Memory-Mapped agent interface is Off.
Port Name Width Direction Function

pr_start

1

Input

A 0 to 1 transition on this port initiates a PR event. You must assert this signal high for a minimum of one clock cycle, and de-assert the signal low prior to the end of the PR operation. This operation ensures the PR Controller IP core is ready to accept the next pr_start trigger event when the freeze signal is low.

The PR Controller IP core ignores this signal during JTAG debug operations.

data[]

1, 8, 16, or 32

Input

Selectable input PR data bus width, either x1, x8, x16, or x32.

Once a PR event triggers, the PR event is synchronous with the rising edge of the clk signal, whenever the data_valid signal is high, and the data_ready signal is high.

The PR Controller IP core ignores this signal during JTAG debug operations.

data_valid

1

Input

A 0 to 1 transition on this port indicates the data[] port contains valid data.

The PR Controller IP core ignores this signal during JTAG debug operations.

data_ready

1

Output

A 0 to 1 transition on this port indicates the PR Controller IP core is ready to read the valid data on the data[] port, whenever the data_valid signal asserts high. The data sender must stop sending valid data if this port is low.

This signal deasserts low during JTAG debug operations.

status[2:0]

1

Output

A 3-bit output that indicates the status of PR events. When the IP detects an error (PR_ERROR, CRC_ERROR, or incompatible bitstream error), this signal latches high. This signal only resets at the beginning of the next PR event, when pr_start is high, and freeze is low. For example:

3’b000 – power-up or nreset asserts

3’b001 – PR_ERROR triggers

3’b010 – CRC_ERROR triggers

3’b011 – Incompatible bitstream error detection

3’b100 – PR operation in progress

3’b101 – PR operation passes

3'b110 – Reserved bit

3'b111 – Reserved bit

Table 26.   Avalon® Memory-Mapped Slave Interface PortsThese signals are available when Enable Avalon® memory-mapped slave interface is On.
Port Name Width Direction Function

avmm_slave_address

4

Input

Avalon® memory-mapped address bus. The address bus is in the unit of Word addressing.

The PR Controller IP core ignores this signal during JTAG debug operations.

avmm_slave_read 1

Input

Avalon® memory-mapped read control.

The PR Controller IP core ignores this signal during JTAG debug operations.

avmm_slave_readdata 32

Output

Avalon® memory-mapped read data bus.

The PR Controller IP core ignores this signal during JTAG debug operations.

avmm_slave_write 1

Input

Avalon® memory-mapped write control.

The PR Controller IP core ignores this signal during JTAG debug operations.

avmm_slave_writedata 32

Input

Avalon® memory-mapped write data bus.

The PR Controller IP core ignores this signal during JTAG debug operations.

avmm_slave_waitrequest 1

Output

Indicates that the IP is busy. Also indicates that the IP core is unable to respond to a read or write request.

The IP core pulls this signal high during JTAG debug operations.

Table 27.  Interrupt Interface PortsThese ports are available when Enable interrupt interface is On.
Port Name Width Direction Function

irq

1

Output

The interrupt signal.

Table 28.  CRC BLOCK InterfaceThese ports are available when Use as Partial Reconfiguration Internal Host is Off, or when you instantiate the CRCBLOCK manually for an internal host.
Port Name Width Direction Function

crc_error_pin

1

Input

Available when you use the PR Controller IP core as an External Host. Connect this port to the dedicated CRC_ERROR pin of the FPGA undergoing partial reconfiguration.

Table 29.   PR Block InterfaceThese options are available when Use as Partial Reconfiguration Internal Host is Off, or when you instantiate the PRBLOCK manually for an internal host.
Port Name Width Direction Function

pr_ready_pin

1

Input

Connect this port to the dedicated PR_READY pin of the FPGA undergoing partial reconfiguration.

pr_error_pin

1

Input

Connect this port to the dedicated PR_ERROR pin of the FPGA undergoing partial reconfiguration.

pr_done_pin

1

Input

Connect this port to the dedicated PR_DONE pin of the FPGA undergoing partial reconfiguration.

pr_request_pin

1

Output

Connect this port to the dedicated PR_REQUEST pin of the FPGA undergoing partial reconfiguration.

pr_clk_pin

1

Output

Connect this port to the dedicated DCLK of the FPGA undergoing partial reconfiguration.

pr_data_pin[31..0]

16|32

Output

Connect this port to the dedicated DATA[31..0] pins of the FPGA undergoing partial reconfiguration.