F-Tile Triple-Speed Ethernet Intel® FPGA IP User Guide

Download PDF
ID 741328
Date 4/15/2024
Public
Document Table of Contents
Document Table of Contents x
1. About the F-Tile Triple-Speed Ethernet Intel® FPGA IP User Guide 2. About F-Tile Triple-Speed Ethernet Intel® FPGA IP 3. Getting Started 4. Parameter Settings 5. Functional Description 6. Configuration Register Space 7. Interface Signals 8. Design Considerations 9. Timing Constraints 10. Software Programming Interface 11. F-Tile Triple-Speed Ethernet Intel® FPGA IP User Guide Archives 12. Document Revision History for the F-Tile Triple-Speed Ethernet Intel® FPGA IP User Guide A. Ethernet Frame Format B. Simulation Parameters
2. About F-Tile Triple-Speed Ethernet Intel® FPGA IP x
2.1. Release Information 2.2. Device Family Support 2.3. Features 2.4. 10/100/1000 Ethernet MAC Versus Small MAC 2.5. High-Level Block Diagrams 2.6. Example Applications 2.7. IP Verification 2.8. Performance and Resource Utilization
2.7. IP Verification x
2.7.1. Optical Platform 2.7.2. Copper Platform
3. Getting Started x
3.1. Introduction to Intel® FPGA IP Cores 3.2. Installing and Licensing Intel® FPGA IPs 3.3. Specifying the IP Core Parameters and Options 3.4. IP Core Generation Output 3.5. Simulating Intel® FPGA IP Cores
3.2. Installing and Licensing Intel® FPGA IPs x
3.2.1. Intel® FPGA IP Evaluation Mode
3.4. IP Core Generation Output x
3.4.1. Design Constraint File
4. Parameter Settings x
4.1. Core Configuration 4.2. Ethernet MAC Options 4.3. FIFO Options 4.4. Timestamp Options 4.5. PCS/Transceiver Options
5. Functional Description x
5.1. 10/100/1000 Ethernet MAC 5.2. 1000BASE-X/SGMII PCS With Optional Embedded PMA 5.3. Precision Time Protocol 5.4. Deterministic Latency
5.1. 10/100/1000 Ethernet MAC x
5.1.1. MAC Architecture 5.1.2. MAC Interfaces 5.1.3. MAC Transmit Datapath 5.1.4. MAC Receive Datapath 5.1.5. MAC Transmit and Receive Latencies 5.1.6. FIFO Buffer Thresholds 5.1.7. Congestion and Flow Control 5.1.8. Magic Packets 5.1.9. MAC Local Loopback 5.1.10. MAC Reset 5.1.11. PHY Management (MDIO) 5.1.12. Connecting MAC to External PHYs
5.1.3. MAC Transmit Datapath x
5.1.3.1. IP Payload Re-alignment 5.1.3.2. Address Insertion 5.1.3.3. Frame Payload Padding 5.1.3.4. CRC-32 Generation 5.1.3.5. Interpacket Gap Insertion 5.1.3.6. Collision Detection in Half-Duplex Mode
5.1.4. MAC Receive Datapath x
5.1.4.1. Preamble Processing 5.1.4.2. Collision Detection in Half-Duplex Mode 5.1.4.3. Address Checking 5.1.4.4. Frame Type Validation 5.1.4.5. Payload Pad Removal 5.1.4.6. CRC Checking 5.1.4.7. Length Checking 5.1.4.8. Frame Writing 5.1.4.9. IP Payload Alignment
5.1.4.3. Address Checking x
5.1.4.3.1. Unicast Address Checking 5.1.4.3.2. Multicast Address Resolution
5.1.6. FIFO Buffer Thresholds x
5.1.6.1. Receive Thresholds 5.1.6.2. Transmit Thresholds 5.1.6.3. Transmit FIFO Buffer Underflow
5.1.7. Congestion and Flow Control x
5.1.7.1. Remote Device Congestion 5.1.7.2. Receive FIFO Buffer and Local Device Congestion
5.1.8. Magic Packets x
5.1.8.1. Sleep Mode 5.1.8.2. Magic Packet Detection
5.1.11. PHY Management (MDIO) x
5.1.11.1. MDIO Connection 5.1.11.2. MDIO Frame Format
5.1.12. Connecting MAC to External PHYs x
5.1.12.1. Gigabit Ethernet 5.1.12.2. Programmable 10/100 Ethernet 5.1.12.3. Programmable 10/100/1000 Ethernet Operation
5.2. 1000BASE-X/SGMII PCS With Optional Embedded PMA x
5.2.1. 1000BASE-X/SGMII PCS Architecture 5.2.2. Transmit Operation 5.2.3. Receive Operation 5.2.4. Transmit and Receive Latencies 5.2.5. GMII Converter 5.2.6. SGMII Converter 5.2.7. Auto-Negotiation 5.2.8. Ten-bit Interface 5.2.9. 1000BASE-X/SGMII PCS Reset
5.2.2. Transmit Operation x
5.2.2.1. Frame Encapsulation 5.2.2.2. 8b/10b Encoding
5.2.3. Receive Operation x
5.2.3.1. Comma Detection 5.2.3.2. 8b/10b Decoding 5.2.3.3. Frame De-encapsulation 5.2.3.4. Synchronization 5.2.3.5. Carrier Sense 5.2.3.6. Collision Detection
5.2.6. SGMII Converter x
5.2.6.1. Transmit 5.2.6.2. Receive
5.2.7. Auto-Negotiation x
5.2.7.1. 1000BASE-X Auto-Negotiation 5.2.7.2. SGMII Auto-Negotiation
5.3. Precision Time Protocol x
5.3.1. IEEE 1588v2 Supported Configurations 5.3.2. IEEE 1588v2 Features 5.3.3. IEEE 1588v2 Architecture 5.3.4. IEEE 1588v2 Transmit Datapath 5.3.5. IEEE 1588v2 Receive Datapath 5.3.6. IEEE 1588v2 Frame Format
5.3.6. IEEE 1588v2 Frame Format x
5.3.6.1. PTP Frame in IEEE 802.3 5.3.6.2. PTP Frame over UDP/IPv4 5.3.6.3. PTP Frame over UDP/IPv6
6. Configuration Register Space x
6.1. MAC Configuration Register Space 6.2. PCS Configuration Register Space 6.3. Register Initialization
6.1. MAC Configuration Register Space x
6.1.1. Base Configuration Registers (Dword Offset 0x00 – 0x17) 6.1.2. Statistics Counters (Dword Offset 0x18 – 0x38) 6.1.3. Transmit and Receive Command Registers (Dword Offset 0x3A – 0x3B) 6.1.4. Supplementary Address (Dword Offset 0xC0 – 0xC7) 6.1.5. IEEE 1588v2 Feature (Dword Offset 0xD0 – 0xD6) 6.1.6. Deterministic Latency (Dword Offset 0xE1– 0xE3) 6.1.7. IEEE 1588v2 Feature PMA Delay
6.1.1. Base Configuration Registers (Dword Offset 0x00 – 0x17) x
6.1.1.1. Command_Config Register (Dword Offset 0x02)
6.2. PCS Configuration Register Space x
6.2.1. Control Register (Word Offset 0x00) 6.2.2. Status Register (Word Offset 0x01) 6.2.3. Dev_Ability and Partner_Ability Registers (Word Offset 0x04 – 0x05) 6.2.4. An_Expansion Register (Word Offset 0x06) 6.2.5. If_Mode Register (Word Offset 0x14)
6.2.3. Dev_Ability and Partner_Ability Registers (Word Offset 0x04 – 0x05) x
6.2.3.1. 1000BASE-X 6.2.3.2. SGMII MAC Mode Auto Negotiation 6.2.3.3. SGMII PHY Mode Auto Negotiation
6.3. Register Initialization x
6.3.1. Triple-Speed Ethernet System with MII/GMII 6.3.2. Triple-Speed Ethernet System with SGMII 6.3.3. Triple-Speed Ethernet System with 1000BASE-X Interface
7. Interface Signals x
7.1. Interface Signals 7.2. Timing
7.1. Interface Signals x
7.1.1. 10/100/1000 Ethernet MAC Signals 7.1.2. 10/100/1000 Multiport Ethernet MAC Signals 7.1.3. 10/100/1000 Ethernet MAC with 1000BASE-X/SGMII PCS Signals 7.1.4. 10/100/1000 Ethernet MAC with 1000BASE-X/SGMII 2XTBI PCS and Embedded PMA Signals (F-Tile) 7.1.5. 10/100/1000 Ethernet MAC Without Internal FIFO Buffers with 1000BASE-X/SGMII 2XTBI PCS Signals 7.1.6. 10/100/1000 Ethernet MAC Without Internal FIFO Buffers with IEEE 1588v2 , 1000BASE-X/SGMII 2XTBI PCS, and Embedded Serial PMA Signals 7.1.7. 10/100/1000 Multiport Ethernet MAC with 1000BASE-X/SGMII PCS Signals 7.1.8. 10/100/1000 Ethernet MAC with 1000BASE-X/SGMII PCS and Embedded PMA Signals 7.1.9. 10/100/1000 Multiport Ethernet MAC with 1000BASE-X/SGMII PCS and Embedded PMA Signals 7.1.10. 1000BASE-X/SGMII PCS Signals 7.1.11. 1000BASE-X/SGMII 2XTBI PCS Signals 7.1.12. 1000BASE-X/SGMII PCS and PMA Signals
7.1.1. 10/100/1000 Ethernet MAC Signals x
7.1.1.1. Clock and Reset Signals 7.1.1.2. Clock Enabler Signals 7.1.1.3. MAC Control Interface Signals 7.1.1.4. MAC Status Signals 7.1.1.5. MAC Receive Interface Signals 7.1.1.6. MAC Transmit Interface Signals 7.1.1.7. Pause and Magic Packet Signals 7.1.1.8. MII/GMII/RGMII Signals 7.1.1.9. PHY Management Signals 7.1.1.10. ECC Status Signals
7.1.2. 10/100/1000 Multiport Ethernet MAC Signals x
7.1.2.1. Multiport MAC Clock and Reset Signals 7.1.2.2. Multiport MAC Receive Interface Signals 7.1.2.3. Multiport MAC Transmit Interface Signals 7.1.2.4. Multiport MAC Packet Classification Signals 7.1.2.5. Multiport MAC FIFO Status Signals
7.1.3. 10/100/1000 Ethernet MAC with 1000BASE-X/SGMII PCS Signals x
7.1.3.1. TBI Interface Signals 7.1.3.2. Status LED Control Signals 7.1.3.3. SERDES Control Signals 7.1.3.4. ECC Status Signals
7.1.4. 10/100/1000 Ethernet MAC with 1000BASE-X/SGMII 2XTBI PCS and Embedded PMA Signals (F-Tile) x
7.1.4.1. GMII Clock Signals 7.1.4.2. F-Tile Transceiver Direct PHY Signals
7.1.6. 10/100/1000 Ethernet MAC Without Internal FIFO Buffers with IEEE 1588v2 , 1000BASE-X/SGMII 2XTBI PCS, and Embedded Serial PMA Signals x
7.1.6.1. Deterministic Latency Clock Signals 7.1.6.2. IEEE 1588v2 RX Timestamp Signals 7.1.6.3. IEEE 1588v2 TX Timestamp Signals 7.1.6.4. IEEE 1588v2 TX Timestamp Request Signals 7.1.6.5. IEEE 1588v2 TX Insert Control Timestamp Signals 7.1.6.6. IEEE 1588v2 Time-of-Day (TOD) Clock Interface Signals 7.1.6.7. IEEE 1588v2 PCS Phase Measurement Clock Signal
7.1.8. 10/100/1000 Ethernet MAC with 1000BASE-X/SGMII PCS and Embedded PMA Signals x
7.1.8.1. 1.25 Gbps Serial Interface 7.1.8.2. Transceiver Native PHY Signal 7.1.8.3. Intel LVDS Transmitter and Receiver Soft-CDR I/O Signals
7.1.10. 1000BASE-X/SGMII PCS Signals x
7.1.10.1. PCS Control Interface Signals 7.1.10.2. PCS Reset Signals 7.1.10.3. MII/GMII Clocks and Clock Enablers 7.1.10.4. GMII 7.1.10.5. MII 7.1.10.6. SGMII Status Signals
7.1.11. 1000BASE-X/SGMII 2XTBI PCS Signals x
7.1.11.1. Clock Enablers 7.1.11.2. PCS Reset Signals 7.1.11.3. TBI Interface Signals
7.2. Timing x
7.2.1. Avalon Streaming Receive Interface 7.2.2. Avalon Streaming Transmit Interface 7.2.3. GMII Transmit 7.2.4. GMII Receive 7.2.5. RGMII Transmit 7.2.6. RGMII Receive 7.2.7. MII Transmit 7.2.8. MII Receive 7.2.9. IEEE 1588v2 Timestamp
8. Design Considerations x
8.1. Optimizing Clock Resources in Multiport MAC with PCS and Embedded PMA 8.2. Sharing PLLs in Devices with LVDS Soft-CDR I/O 8.3. Exposed Ports in the New User Interface 8.4. Clocking Scheme of MAC with 2XTBI PCS and Embedded PMA
8.1. Optimizing Clock Resources in Multiport MAC with PCS and Embedded PMA x
8.1.1. MAC and PCS With LVDS Soft-CDR I/O
9. Timing Constraints x
9.1. Creating Clock Constraints 9.2. Recommended Clock Frequency
10. Software Programming Interface x
10.1. Driver Architecture 10.2. Directory Structure 10.3. PHY Definition 10.4. Using Multiple SG-DMA Descriptors 10.5. Using Jumbo Frames 10.6. API Functions 10.7. Constants
10.6. API Functions x
10.6.1. alt_tse_mac_get_common_speed() 10.6.2. alt_tse_mac_set_common_speed() 10.6.3. alt_tse_phy_add_profile() 10.6.4. alt_tse_system_add_sys() 10.6.5. triple_speed_ethernet_init() 10.6.6. tse_mac_close() 10.6.7. tse_mac_raw_send() 10.6.8. tse_mac_setGMII mode() 10.6.9. tse_mac_setMIImode() 10.6.10. tse_mac_SwReset()
A. Ethernet Frame Format x
A.1. Basic Frame Format A.2. VLAN and Stacked VLAN Frame Format A.3. Pause Frame Format
A.3. Pause Frame Format x
A.3.1. Pause Frame Generation
B. Simulation Parameters x
B.1. Functionality Configuration Parameters B.2. Test Configuration Parameters
1. About the F-Tile Triple-Speed Ethernet Intel® FPGA IP User Guide
2. About F-Tile Triple-Speed Ethernet Intel® FPGA IP
3. Getting Started
4. Parameter Settings
5. Functional Description
6. Configuration Register Space
7. Interface Signals
8. Design Considerations
9. Timing Constraints
10. Software Programming Interface
11. F-Tile Triple-Speed Ethernet Intel® FPGA IP User Guide Archives
12. Document Revision History for the F-Tile Triple-Speed Ethernet Intel® FPGA IP User Guide
A. Ethernet Frame Format
B. Simulation Parameters

8.4. Clocking Scheme of MAC with 2XTBI PCS and Embedded PMA

The following is the clocking scheme of the design that contains MAC with 2XTBI and embedded PMA on F-Tile :
  • 2XTBI PCS runs on 125 MHz and 62.5 MHz clocks while the same 125 MHz clock is used by MAC.
  • The 125 MHz and 62.5 MHz clocks must be synchronous, in which their rising edges must align and must have 0 ppm and phase shift.
  • The F-Tile Direct PHY are the embedded PMAs in this variant. The tx_clkout and rx_clkout on the F-Tile Direct PHY are used as clock sources for 2XTBI PCS tbi2x_tx_clk and tbi2x_rx_clk.
  • Logic is implemented in the PCS block for clock rate matching by default regardless whether the ENABLE_SGMII option is selected. Therefore, the 125 MHz and 62.5 MHz clocks do not need to be at 0 ppm in comparison with tx_clkout and rx_clkout, which are usually provided by external SERDES.
  • The F-Tile Direct PHY transceivers are driven by the 156.25 MHz clock.
  • The reference clock input to the F-Tile Direct PHY, tx_pll_refclk_link and rx_cdr_refclk_link, should be driven by the 156.25 MHz system PLL output.
Table 101.  Clock Signals Visible at Top-Level DesignClock signals that are visible at the top-level design for each possible configuration.
Clocks Configurations 18
MAC and 2XTBI PCS with PMA 2XTBI PCS Only
clk Yes N/A
reg_clk No Yes
ff_tx_clk Yes N/A
ff_rx_clk Yes N/A
tx_clk_125 Yes Yes
rx_clk_125 Yes Yes
tx_clk_62_5 Yes Yes
rx_clk_62_5 Yes Yes
tbi2x_tx_clk No Yes
tbi2x_rx_clk No Yes
tx_pll_refclk_link 19 Yes N/A
rx_cdr_refclk_link 19 Yes N/A
Figure 79. Clock Connectivity in MAC with 2XTBI PCS and Embedded PMA (F-Tile)
Notes to Clock Connectivity in MAC with 2XTBI PCS and Embedded PMA (F-Tile):
  1. Intel® recommends that the rx_clk_125, tx_clk_125, rx_clk_62_5, and tx_clk_62_5 share the same clock source.
  2. Therefore, Intel® recommends you use one IOPLL with two output clocks to get the 125 MHz and 62.5 MHz clocks and connect to both the TX and RX datapaths.
  3. rx_clkout and tx_clkout are output clocks generated by the F-Tile transceiver Direct PHY and internally connected to tbi2x_rx_clk and tbi2x_tx_clk in the variant MAC with 2XTBI and embedded PMA.
  4. The reg_clk clock is internally connected to clk in the variant MAC with 2XTBI and embedded PMA. Refer to Register Interface Signals for more information about reg_clk.
  5. Intel recommends 156.25 MHz frequency for this clock source when the F-Tile Reference and System PLL Clocks is used to drive the Triple-Speed Ethernet IP only.

When you enable dynamic reconfiguration, System PLL clock is selected for the datapath clocking mode. TX and RX FIFO is introduced between PCS and PMA via the F-Tile 2XTBI terminator block.

Figure 80. MAC with 2XTBI PCS and Embedded PMA (F-Tile) with F-Tile Transceiver Dynamic Reconfiguration Enabled Functional Block Diagram
  1. In system PLL mode, the tx_clkout and rx_clkout is SYSPLL clock frequency divided by 2. In PMA mode, the tx_clkout and rx_clkout is the PMA clock frequency.
  2. tx_clkout2 and rx_clkout2 coming from PMA to terminator is 62.5 MHz in SYSPLL & PMA Mode.
18 Yes indicates that the clock is visible at the top-level design.

No indicates that the clock is not visible at the top-level design.

N/A indicates that the clock is not applicable for the given configuration.

19 Clock signals of F-Tile transceiver Direct PHY.
Level Two Title