AN 958: Board Design Guidelines

Download PDF
ID 683073
Date 6/26/2023
Public
Document Table of Contents
Document Table of Contents x
1. Power Distribution Network 2. Gigahertz Channel Design Considerations 3. PCB and Stack-Up Design Considerations 4. Device Pin-Map, Checklists, and Connection Guidelines 5. General Board Design Considerations/Guidelines 6. Memory Interfacing Guidelines 7. Power Dissipation and Thermal Management 8. Tools, Models, and Libraries 9. Reference Designs and Development Kits 10. Document Revision History for AN 958: Board Design Guidelines
1. Power Distribution Network x
1.1. Target Impedance Decoupling Method 1.2. Voltage Regulator Selection 1.3. PDN Design Tool 1.4. Plane Capacitance 1.5. Minimization Parasitic Inductances 1.6. Additional Resources
1.1. Target Impedance Decoupling Method x
1.1.1. FDTIM Decoupling Concepts 1.1.2. Select Decoupling CAPS to Meet ZTARGET
1.1.1. FDTIM Decoupling Concepts x
1.1.1.1. Determining the ZTARGET 1.1.1.2. Determining the fTARGET
1.5. Minimization Parasitic Inductances x
1.5.1. VRM 1.5.2. Decaps 1.5.3. Mounting Inductance 1.5.4. Spreading Inductance 1.5.5. Inter-Plane Capacitance 1.5.6. Conclusion
2. Gigahertz Channel Design Considerations x
2.1. Material Selection and Loss 2.2. Routing Guidelines for Gigabit Channel Designs 2.3. Minimizing Adverse Effects of Material Glass Fiber Weaves 2.4. Plane Cut-outs Below Surface Mount Pads 2.5. Transmitter Pre-Emphasis and Receiver Equalization 2.6. Additional Resources
2.2. Routing Guidelines for Gigabit Channel Designs x
2.2.1. Via Optimization Techniques
2.2.1. Via Optimization Techniques x
2.2.1.1. General Routing Guidelines
3. PCB and Stack-Up Design Considerations x
3.1. Material Selection and Loss 3.2. Board Thickness and Vias 3.3. PCB Recommended Layout Footprint Land Pattern
4. Device Pin-Map, Checklists, and Connection Guidelines x
4.1. High Speed Board Design Advisor 4.2. Complete Pin Connection Table by Device 4.3. Pin Connection Guidelines By Device 4.4. Design for Debug with JTAG Pins 4.5. Hot Socketing, POR and Power Sequencing Support 4.6. Implementing OCT 4.7. Unused I/O Pins Guidelines 4.8. Device Breakout Guidelines 4.9. Additional Resources
5. General Board Design Considerations/Guidelines x
5.1. Board Design Process Overview 5.2. Design Security Features in FPGAs 5.3. EMI 5.4. Discrete Component Selection for High-Speed Design 5.5. S-Parameters 5.6. Smith Chart 5.7. AC Versus DC Coupling 5.8. Additional Resources
5.1. Board Design Process Overview x
5.1.1. Material Selection and Loss 5.1.2. Cross Talk Minimization 5.1.3. Power Filtering/Distribution 5.1.4. Unused I/O Pins 5.1.5. Signal Trace Routing 5.1.6. Ground Bounce 5.1.7. Understanding Transmission Lines 5.1.8. Impedance Calculation 5.1.9. Coplanar Wave Guides 5.1.10. Simultaneous Switching Noise Guidelines
5.1.3. Power Filtering/Distribution x
5.1.3.1. Filtering Noise 5.1.3.2. Distributing Power
5.1.5. Signal Trace Routing x
5.1.5.1. Single Ended Trace Routing 5.1.5.2. Differential Trace Routing 5.1.5.3. Skew Minimization 5.1.5.4. Termination Schemes 5.1.5.5. Termination Design Example 5.1.5.6. Discontinuities Related to a Transmission Path
5.1.5.4. Termination Schemes x
5.1.5.4.1. Simple Parallel Termination 5.1.5.4.2. Thevenin Parallel Termination 5.1.5.4.3. Active Parallel Termination 5.1.5.4.4. Series-RC Parallel Termination 5.1.5.4.5. Series Termination 5.1.5.4.6. Differential Pair Termination 5.1.5.4.7. On-Chip Termination
5.1.5.5. Termination Design Example x
5.1.5.5.1. Determine the Delay 5.1.5.5.2. Determine the Bandwidth 5.1.5.5.3. Using Series Termination 5.1.5.5.4. Using Parallel Termination
5.1.5.6. Discontinuities Related to a Transmission Path x
5.1.5.6.1. Inductive Discontinuity 5.1.5.6.2. Capacitive Discontinuity 5.1.5.6.3. Via Discontinuity 5.1.5.6.4. Right-Angle Bends Related to a Transmission Path
5.1.6. Ground Bounce x
5.1.6.1. Design Guidelines 5.1.6.2. Analyzing Ground Bounce 5.1.6.3. Switching Outputs 5.1.6.4. Quiet Outputs 5.1.6.5. Minimizing Lead Inductance
5.1.8. Impedance Calculation x
5.1.8.1. Microstrip Impedance 5.1.8.2. Stripline Impedance 5.1.8.3. Propagation Delay
5.1.8.3. Propagation Delay x
5.1.8.3.1. Microstrip Layout Propagation Delay 5.1.8.3.2. Stripline Layout Propagation Delay
5.1.9. Coplanar Wave Guides x
5.1.9.1. Simple Coplanar Wave Guide 5.1.9.2. Grounded Coplanar Wave Guide 5.1.9.3. Grounded Differential Coplanar Wave Guide
5.4. Discrete Component Selection for High-Speed Design x
5.4.1. Resistors and Capacitors 5.4.2. Inductors and Ferrite Beads 5.4.3. SMA Connectors
6. Memory Interfacing Guidelines x
6.1. DDR3 Board Design Guidelines 6.2. DDR2 Board Design Guidelines 6.3. DDR Board Design Guidelines 6.4. QDR II and QDR II+ 6.5. RLDRAM II 6.6. Additional Resources
7. Power Dissipation and Thermal Management x
7.1. Power Management Guidelines 7.2. Heat Sinking and Thermal Managment for FPGAs 7.3. Additional Resources
8. Tools, Models, and Libraries x
8.1. Design Tools 8.2. I/O Buffer Models 8.3. Device Libraries 8.4. Net Length Reports 8.5. Thermal Models
9. Reference Designs and Development Kits x
9.1. Development Kits
1. Power Distribution Network
2. Gigahertz Channel Design Considerations
3. PCB and Stack-Up Design Considerations
4. Device Pin-Map, Checklists, and Connection Guidelines
5. General Board Design Considerations/Guidelines
6. Memory Interfacing Guidelines
7. Power Dissipation and Thermal Management
8. Tools, Models, and Libraries
9. Reference Designs and Development Kits
10. Document Revision History for AN 958: Board Design Guidelines

5.1.6.1. Design Guidelines

It is recommended to follow the below design methods to reduce ground bounce:

Figure 68. Suggested Via Location that Connects to Capacitor Pad
These design guidelines provide information and help for high-speed logic designs operating over a range of PCB conditions.
  • Add decoupling capacitors for as many VCC/GND pairs as possible.
  • Place the decoupling capacitors as close as possible to the power and ground pins of the device.
  • Add external buffers at the output of a counter to minimize the loading on Intel® device pins.
  • Configure the unused I/O pin as an output pin and then drive the output low. This configuration acts as a virtual ground. Connect this low driving output pin to GNDINT and/or the board's ground plane.
  • Any unused I/O pin may be driven to ground by programming the “programmable ground” bit (one per I/O cell). In doing so, the macrocell does not need to be sacrificed, but can be used as a buried macrocell.
  • When speed is not critical, turn on the slow slew rate logic option.
  • Limit load capacitance by buffering loads with an external device, or by reducing the number of devices that drive the bus.
  • Eliminate sockets whenever possible.
  • Reduce the number of outputs that can switch simultaneously and/or distribute them evenly throughout the device.
  • Move switching outputs close to a package ground pin.
  • Create a programmable ground next to switching pins.
  • Eliminate pull-up resistors or use pull-down resistors.
  • Use multi-layer PCBs that provide separate VCC and ground planes.
  • Add appropriate resistors in series to each of the switching outputs to limit the current flow into each of the outputs.
  • Create synchronous designs that are not affected by momentarily switching pins.
  • Assign I/O pins to minimize local bunching of output pins.
  • Place the power and ground pins next to each other. The total inductance is reduced by mutual inductance, because current flows in opposite directions in power and ground pins.
  • Use a bigger via size to connect the capacitor pad to the power and ground plane to minimize the inductance in decoupling capacitors.
  • Use the wide and short trace between the via and the capacitor pad or place the via adjacent to the capacitor pad. Refer to Figure 68.
  • Use surface mount capacitors to minimize the lead inductance.
  • Use low effective series resistance (ESR) capacitors. The ESR should be < 400 mΩ.
  • Each GND pin/via should be connected to the ground plane individually.
  • To add extra capacitance on the board, Intel recommends placing a ground plane next to each power (VCC) plane. This placement gives zero lead inductance and no ESR. The dielectric thickness between the two planes should be ~5 mils.
Level Two Title