F-Tile Low Latency 50G Ethernet Intel® FPGA IP User Guide

Download PDF
ID 758946
Date 4/03/2024
Public
Document Table of Contents
Document Table of Contents x
1. About the F-Tile Low Latency 50G Ethernet Intel® FPGA IP User Guide 2. About this IP 3. Getting Started 4. F-Tile Low Latency 50G Ethernet Intel® FPGA IP Parameters 5. Functional Description 6. Reset 7. Interfaces and Signal Descriptions 8. Control, Status, and Statistics Register Descriptions 9. Document Revision History for the F-Tile Low Latency 50G Ethernet Intel® FPGA IP User Guide
2. About this IP x
2.1. Release Information 2.2. Features 2.3. Device Family Support 2.4. Performance and Resource Utilization
3. Getting Started x
3.1. Installing and Licensing Intel® FPGA IPs 3.2. Specifying the IP Parameters and Options 3.3. Simulating the IP 3.4. Generated File Structure 3.5. Integrating Your IP in Your Design 3.6. Compiling the Full Design and Programming the FPGA
3.1. Installing and Licensing Intel® FPGA IPs x
3.1.1. Intel® FPGA IP Evaluation Mode
3.5. Integrating Your IP in Your Design x
3.5.1. Pin Assignments 3.5.2. Adding the F-Tile Reference and System PLL Clocks Intel® FPGA IP 3.5.3. Placement Settings for the 50G Ethernet Intel FPGA IP
5. Functional Description x
5.1. F-Tile Low Latency 50G Ethernet Intel® FPGA IP Functional Description 5.2. User Interface to Ethernet Transmission
5.1. F-Tile Low Latency 50G Ethernet Intel® FPGA IP Functional Description x
5.1.1. F-Tile Low Latency 50G Ethernet Intel® FPGA IP TX MAC Datapath 5.1.2. 50 GbE TX PCS 5.1.3. F-Tile Low Latency 50G Ethernet Intel® FPGA IP RX MAC Datapath 5.1.4. Link Fault Signaling Interface 5.1.5. 50 GbE RX PCS 5.1.6. Flow Control
5.1.1. F-Tile Low Latency 50G Ethernet Intel® FPGA IP TX MAC Datapath x
5.1.1.1. Frame Padding 5.1.1.2. Preamble Insertion 5.1.1.3. Inter-Packet Gap Generation and Insertion 5.1.1.4. Frame Check Sequence (CRC32) Insertion
5.1.3. F-Tile Low Latency 50G Ethernet Intel® FPGA IP RX MAC Datapath x
5.1.3.1. IP Preamble Processing 5.1.3.2. IP Malformed Packet Handling 5.1.3.3. Length/Type Field Processing
5.1.3.3. Length/Type Field Processing x
5.1.3.3.1. Length Checking 5.1.3.3.2. RX CRC Checking and Dynamic Forwarding
5.1.6. Flow Control x
5.1.6.1. TX Pause/PFC Flow Control Frame Transmission Request 5.1.6.2. XON/XOFF Pause Frames
5.2. User Interface to Ethernet Transmission x
5.2.1. Order of Transmission 5.2.2. Bit Order For TX and RX Datapaths
7. Interfaces and Signal Descriptions x
7.1. TX MAC Interface to User Logic 7.2. RX MAC Interface to User Logic 7.3. Transceivers 7.4. Transceiver Reconfiguration Signals 7.5. Avalon® Memory-Mapped Management Interface 7.6. Miscellaneous Status and Debug Signals 7.7. Flow Control Signals 7.8. Clock Signals 7.9. Reset Signals
8. Control, Status, and Statistics Register Descriptions x
8.1. TX MAC Registers 8.2. RX MAC Registers 8.3. Pause/PFC Flow Control Registers 8.4. Statistics Registers 8.5. Hard IP Registers
8.4. Statistics Registers x
8.4.1. Statistics Registers
1. About the F-Tile Low Latency 50G Ethernet Intel® FPGA IP User Guide
2. About this IP
3. Getting Started
4. F-Tile Low Latency 50G Ethernet Intel® FPGA IP Parameters
5. Functional Description
6. Reset
7. Interfaces and Signal Descriptions
8. Control, Status, and Statistics Register Descriptions
9. Document Revision History for the F-Tile Low Latency 50G Ethernet Intel® FPGA IP User Guide

3.1.1. Intel® FPGA IP Evaluation Mode

The free Intel® FPGA IP Evaluation Mode allows you to evaluate licensed Intel® FPGA IPs in simulation and hardware before purchase. Intel® FPGA IP Evaluation Mode supports the following evaluations without additional license:
  • Simulate the behavior of a licensed Intel® FPGA IP in your system.
  • Verify the functionality, size, and speed of the IP quickly and easily.
  • Generate time-limited device programming files for designs that include IPs.
  • Program a device with your IP and verify your design in hardware.

Intel® FPGA IP Evaluation Mode supports the following operation modes:

  • Tethered—Allows running the design containing the licensed Intel® FPGA IP indefinitely with a connection between your board and the host computer. Tethered mode requires a serial joint test action group (JTAG) cable connected between the JTAG port on your board and the host computer, which is running the Quartus® Prime Programmer for the duration of the hardware evaluation period. The Programmer only requires a minimum installation of the Quartus® Prime software, and requires no Quartus® Prime license. The host computer controls the evaluation time by sending a periodic signal to the device via the JTAG port. If all licensed IPs in the design support tethered mode, the evaluation time runs until any IP evaluation expires. If all of the IPs support unlimited evaluation time, the device does not time-out.
  • Untethered—Allows running the design containing the licensed IP for a limited time. The IP reverts to untethered mode if the device disconnects from the host computer running the Quartus® Prime software. The IP also reverts to untethered mode if any other licensed IP in the design does not support tethered mode.

When the evaluation time expires for any licensed Intel® FPGA IP in the design, the design stops functioning. All IPs that use the Intel® FPGA IP Evaluation Mode time out simultaneously when any IP in the design times out. When the evaluation time expires, you must reprogram the FPGA device before continuing hardware verification. To extend use of the IP for production, purchase a full production license for the IP.

You must purchase the license and generate a full production license key before you can generate an unrestricted device programming file. During Intel® FPGA IP Evaluation Mode, the Compiler only generates a time-limited device programming file (<project name> _time_limited.sof) that expires at the time limit.

Figure 4.  Intel® FPGA IP Evaluation Mode Flow
Note: Refer to each IP's user guide for parameterization steps and implementation details.

Intel® licenses IPs on a per-seat, perpetual basis. The license fee includes first-year maintenance and support. You must renew the maintenance contract to receive updates, bug fixes, and technical support beyond the first year. You must purchase a full production license for Intel® FPGA IPs that require a production license, before generating programming files that you may use for an unlimited time. During Intel® FPGA IP Evaluation Mode, the Compiler only generates a time-limited device programming file (<project name> _time_limited.sof) that expires at the time limit. To obtain your production license keys, visit the Intel® FPGA Self-Service Licensing Center.

The Intel® FPGA Software License Agreements govern the installation and use of licensed IPs, the Quartus® Prime design software, and all unlicensed IPs.

Related Information
Level Two Title