Agilex™ 7 Embedded Memory User Guide

Download PDF
ID 683241
Date 3/29/2024
Public
Document Table of Contents
Document Table of Contents x
1. Agilex™ 7 Embedded Memory Overview 2. Agilex™ 7 Embedded Memory Architecture and Features 3. Agilex™ 7 Embedded Memory Design Considerations 4. Agilex™ 7 Embedded Memory IP References 5. Agilex™ 7 Embedded Memory Debugging 6. Agilex™ 7 Embedded Memory User Guide Archives 7. Document Revision History for the Agilex™ 7 Embedded Memory User Guide
1. Agilex™ 7 Embedded Memory Overview x
1.1. Agilex™ 7 Embedded Memory Features
2. Agilex™ 7 Embedded Memory Architecture and Features x
2.1. Fabric Network-On-Chip (NoC) in Agilex™ 7 M-Series M20K Blocks 2.2. Byte Enable in Agilex™ 7 Embedded Memory Blocks 2.3. Address Clock Enable Support 2.4. Asynchronous Clear and Synchronous Clear 2.5. Memory Blocks Error Correction Code (ECC) Support 2.6. Agilex™ 7 Embedded Memory Clocking Modes 2.7. Agilex™ 7 Embedded Memory Configurations 2.8. Force-to-Zero 2.9. Coherent Read Memory 2.10. Freeze Logic 2.11. True Dual Port Dual Clock Emulator 2.12. Initial Value of Read and Write Address Registers 2.13. Timing/Power Optimization Feature in M20K Blocks 2.14. Agilex™ 7 Supported Embedded Memory IPs
2.2. Byte Enable in Agilex™ 7 Embedded Memory Blocks x
2.2.1. Byte Enable Controls 2.2.2. Data Byte Output 2.2.3. Byte Enable Behavior
2.5. Memory Blocks Error Correction Code (ECC) Support x
2.5.1. Parity Bit 2.5.2. ECC Parity Flip 2.5.3. ECC Read-During-Write Behavior 2.5.4. Error Correction Code Truth Table
2.6. Agilex™ 7 Embedded Memory Clocking Modes x
2.6.1. Single Clock Mode 2.6.2. Read/Write Clock Mode 2.6.3. Input/Output Clock Mode 2.6.4. Asynchronous/Synchronous Clears in Clocking Modes 2.6.5. Output Read Data in Simultaneous Read/Write 2.6.6. Independent Clock Enables in Clocking Modes
2.7. Agilex™ 7 Embedded Memory Configurations x
2.7.1. Mixed-Width Port Configurations
2.9. Coherent Read Memory x
2.9.1. Forwarding Logic
3. Agilex™ 7 Embedded Memory Design Considerations x
3.1. Consider the Memory Block Selection 3.2. Consider the Concurrent Read Behavior 3.3. Customize Read-During-Write Behavior 3.4. Consider Power-Up State and Memory Initialization 3.5. Reduce Power Consumption 3.6. Avoid Providing Non-Deterministic Input 3.7. Avoid Changing Clock Signals and Other Control Signals Simultaneously 3.8. Advanced Settings in Quartus® Prime Software for Memory 3.9. Consider the Memory Depth Setting 3.10. M20K Embedded Memory Block Input Clock Quality Requirement 3.11. Consider Registering the Memory Output
3.3. Customize Read-During-Write Behavior x
3.3.1. Same-Port Read-During-Write Mode 3.3.2. Mixed-Port Read-During-Write Mode
4. Agilex™ 7 Embedded Memory IP References x
4.1. On Chip Memory RAM and ROM Intel® FPGA IP Cores 4.2. eSRAM Agilex™ FPGA IP 4.3. FIFO Intel® FPGA IP 4.4. Shift Register (RAM-based) Intel® FPGA IP
4.1. On Chip Memory RAM and ROM Intel® FPGA IP Cores x
4.1.1. Release Information for RAM and ROM Intel® FPGA IPs 4.1.2. RAM: 1-PORT Intel® FPGA IP Parameters 4.1.3. RAM: 2-PORT Intel® FPGA IP Parameters 4.1.4. RAM: 4-PORT Intel® FPGA IP Parameters 4.1.5. ROM: 1-PORT Intel® FPGA IP Parameters 4.1.6. ROM: 2-PORT Intel® FPGA IP Parameters 4.1.7. Changing Parameter Settings Manually 4.1.8. RAM and ROM Interface Signals
4.1.7. Changing Parameter Settings Manually x
4.1.7.1. RAM and ROM Parameter Settings
4.2. eSRAM Agilex™ FPGA IP x
4.2.1. Release Information for eSRAM Agilex™ FPGA IP 4.2.2. eSRAM System Features 4.2.3. eSRAM Agilex™ FPGA IP Parameters 4.2.4. eSRAM Agilex™ FPGA IP Interface Signals 4.2.5. eSRAM Timing Diagrams
4.2.2. eSRAM System Features x
4.2.2.1. eSRAM Specifications
4.3. FIFO Intel® FPGA IP x
4.3.1. Release Information for FIFO Intel® FPGA IP 4.3.2. Configuration Methods 4.3.3. Specifications 4.3.4. FIFO Functional Timing Requirements 4.3.5. SCFIFO ALMOST_EMPTY Functional Timing 4.3.6. FIFO Output Status Flag and Latency 4.3.7. FIFO Metastability Protection and Related Options 4.3.8. FIFO Synchronous Clear and Asynchronous Clear Effect 4.3.9. SCFIFO and DCFIFO Show-Ahead Mode 4.3.10. Different Input and Output Width 4.3.11. DCFIFO Timing Constraint Setting 4.3.12. Coding Example for Manual Instantiation 4.3.13. Design Example 4.3.14. Gray-Code Counter Transfer at the Clock Domain Crossing 4.3.15. Guidelines for Embedded Memory ECC Feature 4.3.16. FIFO Intel® FPGA IP Parameters 4.3.17. Reset Scheme
4.3.3. Specifications x
4.3.3.1. Verilog HDL Prototype 4.3.3.2. VHDL Component Declaration 4.3.3.3. VHDL LIBRARY-USE Declaration 4.3.3.4. HDL Code from Parameterizable Macros Template 4.3.3.5. FIFO Signals 4.3.3.6. FIFO Parameter Settings
4.3.8. FIFO Synchronous Clear and Asynchronous Clear Effect x
4.3.8.1. Recovery and Removal Timing Violation Warnings when Compiling a DCFIFO
4.3.11. DCFIFO Timing Constraint Setting x
4.3.11.1. Embedded Timing Constraint 4.3.11.2. User Configurable Timing Constraint
4.3.11.2. User Configurable Timing Constraint x
4.3.11.2.1. SDC Commands
4.4. Shift Register (RAM-based) Intel® FPGA IP x
4.4.1. Release Information for Shift Register (RAM-based) Intel® FPGA IP 4.4.2. Shift Register (RAM-based) Intel® FPGA IP Features 4.4.3. Shift Register (RAM-based) Intel® FPGA IP General Description 4.4.4. Shift Register (RAM-based) Intel® FPGA IP Parameter Settings 4.4.5. Shift Register Ports and Parameters Setting
1. Agilex™ 7 Embedded Memory Overview
2. Agilex™ 7 Embedded Memory Architecture and Features
3. Agilex™ 7 Embedded Memory Design Considerations
4. Agilex™ 7 Embedded Memory IP References
5. Agilex™ 7 Embedded Memory Debugging
6. Agilex™ 7 Embedded Memory User Guide Archives
7. Document Revision History for the Agilex™ 7 Embedded Memory User Guide

1.1. Agilex™ 7 Embedded Memory Features

The Agilex™ 7 devices contain the following types of memory blocks: Embedded SRAM (eSRAM) blocks, M20K blocks, and memory logic array blocks (MLABs).
Table 1.   Agilex™ 7 Embedded Memory and Supported Device Variants
Memory Blocks Description Device Variant Support
eSRAM
  • 18.432 -Megabit (Mb) eSRAM blocks
  • High bandwidth and very high random transaction rate (RTR) on-chip memory block.
  • Each block consists of 8 channels and each channel has 32 banks.
  • Each bank is configurable to 1K depth and 64-bit data width.
  • Supports only simple dual-port RAM with concurrent read and write access per channel.
 Available in select F- and I- Series devices only.
M20K
  • 20-kilobit (Kb) M20K blocks
  • Blocks of dedicated memory resources.
  • Ideal for larger memory arrays, while providing a large number of independent ports.
 Available in all F-, I-, and M-Series devices.
MLABs
  • 640-bit MLABs
  • Memory blocks configured from enhanced dual-purpose logic array blocks (LABs).
  • Ideal for wide and shallow memory arrays.
  • Optimized for implementation of shift registers for digital signal processing (DSP) applications, wide and shallow FIFO buffers, and filter delay lines.
  • Each MLAB is made up of ten adaptive logic modules (ALMs).

In Agilex™ 7 devices, you can configure each ALM in the MLAB as ten 32×2 blocks. The Agilex™ 7 devices provide one 32×20 simple dual-port SRAM block per MLAB.

The Agilex™ 7 embedded memory blocks support the following operation modes:
  • Single-port
  • Simple dual-port
  • True dual-port
  • Simple quad-port
  • ROM
Table 2.   Agilex™ 7 Embedded Memory FeaturesThis table summarizes the features supported by the Agilex™ 7 embedded memory blocks.
Features eSRAM M20K MLAB
Maximum operating frequency 750 MHz
  • 1 GHz (simple dual-port RAM mode)
  • 600 MHz (true dual-port and simple quad-port RAM mode)
 1 GHz
Total RAM bits (including parity bits) 18.432 Mb 20,480 bits 640 bits
Byte enable N/A Supported Supported
Address clock enable

(address stall)

 N/A Supported (only in simple dual-port RAM mode) Supported
Simple dual-port mixed width N/A Supported N/A
FIFO buffer mixed width N/A Supported N/A
Memory Initialization File (.mif) N/A Supported Supported
Dual-clock mode N/A Supported (only in simple dual-port RAM mode) Supported
Full synchronous memory Supported Supported Supported
Asynchronous memory N/A N/A Only for flow-through read memory operations
Power-up state N/A Output ports are cleared
  • Registered output ports are cleared
  • Unregistered output ports read memory contents
Asynchronous/Synchronous Clears N/A
  • Output registers and output latches
  • Supports asynchronous clear on read address registers (only in simple dual-port and simple quad-port modes)
 Output registers and output latches
Write/read operation triggering Rising clock edges Rising clock edges Rising clock edges
Same-port read-during-write N/A Output ports set to New Data , Old Data, or Don't Care Output ports set to Don't Care
Mixed-port read-during-write Write-forwarding feature
  • ON = New Data
  • OFF = Don't Care
  • Simple Dual Port RAM: Output ports set to Old Data or Don't Care
  • True Dual Port RAM: Output ports set to Don't Care
  • Simple Quad Port: Output ports set to new_a_old_b
Output ports set to New Data, Old Data, or Don't Care
Error Correction Code (ECC) support
  • Built-in support ×64-wide simple dual-port mode
  • Built-in support ×32-wide simple dual-port mode
  • Parity bits

N/A
Force-to-Zero N/A Supported N/A
Coherent read memory N/A Supported N/A
Freeze logic N/A Supported N/A
True dual port (TDP) dual clock emulator N/A Supported N/A
Level Two Title