Intel Agilex® 7 Configuration User Guide

ID 683673
Date 4/28/2023
Public

A newer version of this document is available. Customers should click here to go to the newest version.

Document Table of Contents

3.1.7.2.2. PFL II Signals

Table 30.  PFL II Signals
Pin Type Weak Pull-Up Function
pfl_nreset Input Asynchronous reset for the PFL II IP core. Pull high to enable FPGA configuration. To prevent FPGA configuration, pull low when you do not use the PFL II IP core. This pin does not affect the PFL II IP flash programming functionality.
pfl_flash_access_granted Input For system-level synchronization. A processor or any arbiter that controls access to the flash drives this input pin. To use the PFL II IP core function as the flash master pull this pin high. Driving the pfl_flash_access_granted pin low prevents the JTAG interface from accessing the flash and FPGA configuration.
pfl_clk Input User input clock for the device. This is the frequency you specify for the What is the external clock frequency? parameter on the Configuration tab of the PFL II IP. This frequency must not be higher than the maximum DCLK frequency you specify for FPGA during configuration. This pin is not available if you are only using the PFL II IP for flash programming.
fpga_pgm[] Input Determines the page for the configuration. This pin is not available if you are only using the PFL II IP for flash programming.
fpga_conf_done Input 10 kΩ Pull-Up Resistor Connects to the CONF_DONE pin of the FPGA. The FPGA releases the pin high if the configuration is successful. During FPGA configuration, this pin remains low. This pin is not available if you are only using the PFL II IP for flash programming.
fpga_nstatus Input 10 kΩ Pull-Up Resistor Connects to the nSTATUS pin of the FPGA. This pin is high before the FPGA configuration begins and must stay high during FPGA configuration. If a configuration error occurs, the FPGA pulls this pin low and the PFL II IP core stops reading the data from the flash memory device. This pin is not available if you are only using the PFL II IP for flash programming.
pfl_nreconfigure Input

When low initiates FPGA reconfiguration. To implement manual control of reconfiguration connect this pin to a switch. You can use this input to write your own logic in a CPLD to trigger reconfiguration via the PFL II IP. You can use pfl_nreconfigure to drive the fpga_nconfig output signal initiating reconfiguration. The pfl_clk pin registers this signal. This pin is not available if you are only using the PFL II IP for flash programming.

pfl_flash_access_request Output For system-level synchronization. When necessary, this pin connects to a processor or an arbiter. The PFL II IP core drives this pin high when the JTAG interface accesses the flash or the PFL II IP configures the FPGA. This output pin works in conjunction with the flash_noe and flash_nwe pins.
flash_addr[] Output The flash memory address. The width of the address bus depends on the density of the flash memory device and the width of the flash_data bus. Intel recommends that you turn On the Set flash bus pins to tri-state when not in use option in the PFL II .
flash_data[] Input or Output (bidirectional pin) Bidirectional data bus to transmit or receive 8-, 16-, or 32-bit data. Intel recommends that you turn On the Set flash bus pins to tri-state when not in use option in the PFL II. 10 trp1477472110552.html#trp1477472110552__fn_alterarecommendsnotinserting
flash_nce[] Output Connects to the nCE pin of the flash memory device. A low signal enables the flash memory device. Use this bus for multiple flash memory device support. The flash_nce pin connects to each nCE pin of all the connected flash memory devices. The width of this port depends on the number of flash memory devices in the chain. 11 trp1477472110552.html#trp1477472110552__fn_alterarecommendsnotinserting
flash_nwe Output Connects to the nWE pin of the flash memory device. When low enables write operations to the flash memory device.
flash_noe Output Connects to the nOE pin of the flash memory device. When low enables the outputs of the flash memory device during a read operation.
flash_clk Output For burst mode. Connects to the CLK input pin of the flash memory device. The active edges of CLK increment the flash memory device internal address counter. The flash_clk frequency is half of the pfl_clk frequency in burst mode for a single CFI flash. In dual CFI flash solution, the flash_clk frequency runs at a quarter of the pfl_clk frequency. Use this pin for burst mode only. Do not connect these pins from the flash memory device to the host if you are not using burst mode.
flash_nadv Output For burst mode. Connects to the address valid input pin of the flash memory device. Use this signal to latch the start address. Use this pin for burst mode only. Do not connect these pins from the flash memory device to the host if you are not using burst mode.
flash_nreset Output Connects to the reset pin of the flash memory device. A low signal resets the flash memory device.
fpga_nconfig Open Drain Output 10-kW Pull-Up Resistor Connects to the nCONFIG pin of the FPGA. A low pulse resets the FPGA and initiates configuration. These pins are not available for the flash programming option in the PFL II IP core. trp1477472110552.html#trp1477472110552__fn_alterarecommendsnotinserting
pfl_reset_watchdog Input A switch signal to reset the watchdog timer before the watchdog timer times out. To reset the watchdog timer hold the signal high or low for at least two pfl_clk clock cycles.
pfl_watchdog_error Output When high indicates an error condition to the watchdog timer.
10 Intel recommends that you do not insert logic between the PFL II pins and the host I/O pins, especially on the flash_data and fpga_nconfig pins.
11 Intel recommends that you do not insert logic between the PFL II pins and the host I/O pins, especially on the flash_data and fpga_nconfig pins.