EPCQ-A Serial Configuration Device Datasheet

Download PDF
ID 683818
Date 10/01/2019
Public
Document Table of Contents
Document Table of Contents x
1. EPCQ-A Serial Configuration Device Datasheet
1. EPCQ-A Serial Configuration Device Datasheet x
1.1. Supported Devices 1.2. Features 1.3. Operating Conditions 1.4. Pin Information 1.5. Device Package and Ordering Code 1.6. Memory Array Organization 1.7. Memory Operations 1.8. Status Register 1.9. Summary of Operation Codes 1.10. Power Mode 1.11. Timing Information 1.12. Programming and Configuration File Support 1.13. Appendix: SFDP Register Definitions 1.14. Document Revision History for the EPCQ-A Serial Configuration Device Datasheet
1.3. Operating Conditions x
1.3.1. Absolute Maximum Ratings 1.3.2. Recommended Operating Conditions 1.3.3. DC Operating Conditions 1.3.4. AC Measurement Conditions 1.3.5. ICC Supply Current 1.3.6. Capacitance
1.4. Pin Information x
1.4.1. Pin-Out Diagram for EPCQ4A, EPCQ16A and EPCQ32A Devices 1.4.2. Pin-Out Diagram for EPCQ64A and EPCQ128A Devices 1.4.3. EPCQ-A Device Pin Description
1.5. Device Package and Ordering Code x
1.5.1. Package 1.5.2. Ordering Code
1.6. Memory Array Organization x
1.6.1. Address Range for EPCQ4A 1.6.2. Address Range for EPCQ16A 1.6.3. Address Range for EPCQ32A 1.6.4. Address Range for EPCQ64A 1.6.5. Address Range for EPCQ128A
1.7. Memory Operations x
1.7.1. Timing Requirements
1.8. Status Register x
1.8.1. Read Status Operation 1.8.2. Write Status Operation
1.9. Summary of Operation Codes x
1.9.1. Read Bytes Operation (03h) 1.9.2. Fast Read Operation (0Bh) 1.9.3. Extended Dual Input Fast Read Operation (BBh) 1.9.4. Extended Quad Input Fast Read Operation (EBh) 1.9.5. Read Device Identification Operation (9Fh) 1.9.6. Read Silicon Identification Operation (ABh) 1.9.7. Write Enable Operation (06h) 1.9.8. Write Disable Operation (04h) 1.9.9. Write Bytes Operation (02h) 1.9.10. Quad Input Fast Write Bytes Operation (32h) 1.9.11. Erase Bulk Operation (C7h) 1.9.12. Erase Sector Operation (D8h) 1.9.13. Erase Subsector Operation (20h) 1.9.14. Read SFDP Register Operation (5Ah)
1.11. Timing Information x
1.11.1. Write Operation Timing 1.11.2. Read Operation Timing
1. EPCQ-A Serial Configuration Device Datasheet

1.9.11. Erase Bulk Operation (C7h)

This operation sets all the memory bits to 1 or 0xFF. Similar to the write bytes operation, you must execute the write enable operation before the erase bulk operation.

You can implement the erase bulk operation by driving the nCS signal low and then shifting in the erase bulk operation code on the DATA0 pin. The nCS signal must be driven high after the eighth bit of the erase bulk operation code has been latched in.

Figure 16. Erase Bulk Operation Timing Diagram


The device initiates a self-timed erase bulk cycle immediately after the nCS signal is driven high. For details about the self-timed erase bulk cycle time, refer to tEB in the related information below.

You must account for this delay before accessing the memory contents. Alternatively, you can check the write in progress bit in the status register by executing the read status operation while the self-timed erase cycle is in progress. The write in progress bit is set to 1 during the self-timed erase cycle and 0 when it is complete. The write enable latch bit in the status register is reset to 0 before the erase cycle is complete.

Level Two Title