Device-Specific Power Delivery Network (PDN) Tool 2.0 User Guide

Download PDF
ID 683293
Date 8/24/2021
Public
Document Table of Contents
Document Table of Contents x
1. Device-Specific Power Delivery Network (PDN) Tool 2.0 User Guide
1. Device-Specific Power Delivery Network (PDN) Tool 2.0 User Guide x
1.1. Overview 1.2. PDN Decoupling Methodology Review 1.3. PDN Tool Setup and Result Optimization 1.4. Device-Specific PDN Tool 2.0 Known Issues and Their Solutions 1.5. Document Revision History for the Device-Specific Power Delivery Network (PDN) Tool 2.0 User Guide
1.2. PDN Decoupling Methodology Review x
1.2.1. PDN Circuit Topology 1.2.2. Major Tabs of the PDN Tool 2.0 1.2.3. Design PCB Decoupling Using the PDN Tool 2.0 1.2.4. Troubleshooting ZEFF
1.2.1. PDN Circuit Topology x
1.2.1.1. ZTARGET 1.2.1.2. FEFFECTIVE
1.2.2. Major Tabs of the PDN Tool 2.0 x
1.2.2.1. System_Decap 1.2.2.2. Stackup 1.2.2.3. BGA_Via 1.2.2.4. Plane_Cap 1.2.2.5. Cap_Mount 1.2.2.6. X2Y_Mount 1.2.2.7. Library 1.2.2.8. Enlarged_Graph
1.2.2.1. System_Decap x
1.2.2.1.1. Device Selection Section 1.2.2.1.2. Power Rail Data and Configuration Section 1.2.2.1.3. Meeting Target Impedance when Entering 0 A into the PDN Tool 1.2.2.1.4. Dealing with Multiple Shared Power Supply Pin Types 1.2.2.1.5. VRM Data Section 1.2.2.1.6. Rail Group Summary Section 1.2.2.1.7. VRM Impedance Section 1.2.2.1.8. BGA Via Section 1.2.2.1.9. Plane Section 1.2.2.1.10. Spreading Section 1.2.2.1.11. Implementing Split Planes 1.2.2.1.12. FEFFECTIVE Section 1.2.2.1.13. Decoupling Section 1.2.2.1.14. Results Summary Section 1.2.2.1.15. Recommended Flow for Deriving Decoupling for an FPGA System using the System_Decap Tab
1.2.2.2. Stackup x
1.2.2.2.1. Stackup Data 1.2.2.2.2. Full Stackup
1.2.2.7. Library x
1.2.2.7.1. Two-Terminal Decoupling Capacitors 1.2.2.7.2. Bulk Capacitors 1.2.2.7.3. X2Y Decoupling Capacitors 1.2.2.7.4. BGA Via and Plane Capacitance 1.2.2.7.5. VRM Library 1.2.2.7.6. Spreading R and L Parasitics 1.2.2.7.7. Dielectric Material Library 1.2.2.7.8. User Set FEFFECTIVE
1.2.3. Design PCB Decoupling Using the PDN Tool 2.0 x
1.2.3.1. Pre-Layout Instructions 1.2.3.2. Deriving Decoupling in a Single-Rail Scenario 1.2.3.3. Deriving Decoupling in the Power-Sharing Scenarios
1.2.4. Troubleshooting ZEFF x
1.2.4.1. Strategies for Correcting a High ZEFF
1.3. PDN Tool Setup and Result Optimization x
1.3.1. Setting Up a PCB Stackup 1.3.2. Setting up a Power Group 1.3.3. Optimizing in Pre-Layout 1.3.4. Further Optimizing for Better Accuracy 1.3.5. Correlation
1.3.1. Setting Up a PCB Stackup x
1.3.1.1. Selecting Your Device 1.3.1.2. Inputting Stackup Data
1.3.1.2. Inputting Stackup Data x
1.3.1.2.1. Using a Custom Dielectric Material
1.3.2. Setting up a Power Group x
1.3.2.1. Selecting the Rails 1.3.2.2. Rail Group Summary 1.3.2.3. VRM Impedance 1.3.2.4. BGA Via 1.3.2.5. Calculating Plane 1.3.2.6. Plane Spreading Parasitics 1.3.2.7. FEFFECTIVE and Decoupling Result Summary
1.3.3. Optimizing in Pre-Layout x
1.3.3.1. Checking the Capacitor Model 1.3.3.2. Optimizing the Decap Count
1. Device-Specific Power Delivery Network (PDN) Tool 2.0 User Guide

1.2.2.1.4. Dealing with Multiple Shared Power Supply Pin Types

You cannot add currents from multiple shared power supply pin types and enter them into a single supply pin type using the Intel® Power Distribution Network (PDN) tool.

The PDN tool calculates effective impedance based on the number of pins and package parasitic information for the chosen device. Entering the sum of shared currents into a single power supply pin type causes the PDN tool to miscalculate the spreading inductance. You should always enter the correct current for each power supply pin type into the PDN tool.

Example 1

If a shared 1.2 V power supply consists of VCCIO2A and VCCIO2B, each drawing 0.3 A for a total of 0.6 A, you should not enter 0.6 A for VCCIO2A and 0 A for VCCIO2B.

Instead, you should enter 0.3 A for VCCIO2A and 0.3 A for VCCIO2B.

Example 2

If a shared 1.03 V power supply consisting of VCCR_GXBL1C, VCCR_GXBL1D, VCCT_GXBL1C, and VCCT_GXBL1D drawing 0.5 A, 0.5 A, 0.2 A, and 0.2 A respectively, you should not enter 1 A for VCCR_GXBL1C and 0.4 A for VCCT_GXBL1C.

Instead, you should enter VCCR_GXBL1C = 0.5 A, VCCR_GXBL1D = 0.5 A, VCCT_GXBL1C = 0.2 A, and VCCT_GXBL1D = 0.2 A.

Level Two Title