Device-Specific Power Delivery Network (PDN) Tool 2.0 User Guide

Download PDF
ID 683293
Date 8/24/2021
Public
Document Table of Contents
Document Table of Contents x
1. Device-Specific Power Delivery Network (PDN) Tool 2.0 User Guide
1. Device-Specific Power Delivery Network (PDN) Tool 2.0 User Guide x
1.1. Overview 1.2. PDN Decoupling Methodology Review 1.3. PDN Tool Setup and Result Optimization 1.4. Device-Specific PDN Tool 2.0 Known Issues and Their Solutions 1.5. Document Revision History for the Device-Specific Power Delivery Network (PDN) Tool 2.0 User Guide
1.2. PDN Decoupling Methodology Review x
1.2.1. PDN Circuit Topology 1.2.2. Major Tabs of the PDN Tool 2.0 1.2.3. Design PCB Decoupling Using the PDN Tool 2.0 1.2.4. Troubleshooting ZEFF
1.2.1. PDN Circuit Topology x
1.2.1.1. ZTARGET 1.2.1.2. FEFFECTIVE
1.2.2. Major Tabs of the PDN Tool 2.0 x
1.2.2.1. System_Decap 1.2.2.2. Stackup 1.2.2.3. BGA_Via 1.2.2.4. Plane_Cap 1.2.2.5. Cap_Mount 1.2.2.6. X2Y_Mount 1.2.2.7. Library 1.2.2.8. Enlarged_Graph
1.2.2.1. System_Decap x
1.2.2.1.1. Device Selection Section 1.2.2.1.2. Power Rail Data and Configuration Section 1.2.2.1.3. Meeting Target Impedance when Entering 0 A into the PDN Tool 1.2.2.1.4. Dealing with Multiple Shared Power Supply Pin Types 1.2.2.1.5. VRM Data Section 1.2.2.1.6. Rail Group Summary Section 1.2.2.1.7. VRM Impedance Section 1.2.2.1.8. BGA Via Section 1.2.2.1.9. Plane Section 1.2.2.1.10. Spreading Section 1.2.2.1.11. Implementing Split Planes 1.2.2.1.12. FEFFECTIVE Section 1.2.2.1.13. Decoupling Section 1.2.2.1.14. Results Summary Section 1.2.2.1.15. Recommended Flow for Deriving Decoupling for an FPGA System using the System_Decap Tab
1.2.2.2. Stackup x
1.2.2.2.1. Stackup Data 1.2.2.2.2. Full Stackup
1.2.2.7. Library x
1.2.2.7.1. Two-Terminal Decoupling Capacitors 1.2.2.7.2. Bulk Capacitors 1.2.2.7.3. X2Y Decoupling Capacitors 1.2.2.7.4. BGA Via and Plane Capacitance 1.2.2.7.5. VRM Library 1.2.2.7.6. Spreading R and L Parasitics 1.2.2.7.7. Dielectric Material Library 1.2.2.7.8. User Set FEFFECTIVE
1.2.3. Design PCB Decoupling Using the PDN Tool 2.0 x
1.2.3.1. Pre-Layout Instructions 1.2.3.2. Deriving Decoupling in a Single-Rail Scenario 1.2.3.3. Deriving Decoupling in the Power-Sharing Scenarios
1.2.4. Troubleshooting ZEFF x
1.2.4.1. Strategies for Correcting a High ZEFF
1.3. PDN Tool Setup and Result Optimization x
1.3.1. Setting Up a PCB Stackup 1.3.2. Setting up a Power Group 1.3.3. Optimizing in Pre-Layout 1.3.4. Further Optimizing for Better Accuracy 1.3.5. Correlation
1.3.1. Setting Up a PCB Stackup x
1.3.1.1. Selecting Your Device 1.3.1.2. Inputting Stackup Data
1.3.1.2. Inputting Stackup Data x
1.3.1.2.1. Using a Custom Dielectric Material
1.3.2. Setting up a Power Group x
1.3.2.1. Selecting the Rails 1.3.2.2. Rail Group Summary 1.3.2.3. VRM Impedance 1.3.2.4. BGA Via 1.3.2.5. Calculating Plane 1.3.2.6. Plane Spreading Parasitics 1.3.2.7. FEFFECTIVE and Decoupling Result Summary
1.3.3. Optimizing in Pre-Layout x
1.3.3.1. Checking the Capacitor Model 1.3.3.2. Optimizing the Decap Count
1. Device-Specific Power Delivery Network (PDN) Tool 2.0 User Guide

1.2.3.3. Deriving Decoupling in the Power-Sharing Scenarios

It is a common practice that several power rails in the FPGA device share the same power supply. For example, you can connect VCCPT, VCCA_PLL, and VCCA_FPLL rails that require the same supply voltage to the same PCB power plane. This can be required by the design, such as in the memory interface case. This can also come from the need to reduce bill of materials (BOM) cost. You can use the System_Decap tab to facilitate the decoupling design for the power sharing scenarios.

When deriving decoupling capacitors for multiple FPGAs sharing the same power plane, each FPGA should be analyzed separately using the PDN tool 2.0. For each FPGA design, combine the required power rails as described above and analyze the decoupling scheme as if the FPGA was the only device on the power rail, taking note of how the current is divided across the devices.

High frequency decoupling capacitors are meant to provide the current needed for AC transitions, and must be placed in a close proximity to the FPGA power pins. Thus, the PDN tool 2.0 should be used to derive the required decoupling capacitors for the unique power requirements for each FPGA on the board.

The power regulators must be able to supply the total combined current requirements for each load on the supply, but the decoupling capacitor selections should be analyzed on a single FPGA basis.

Level Two Title